Retro 
Country
Modern
You will need:
Hair dryer
Fishing line
Heat the adhesive
Unscrew the bottle that has been attached to the soap bottle holder and take out a hair dryer. Heat from a hair dryer is the most effective method for softening adhesive. By using a hair dryer and holding it a few centimetres from the adhesive, the heat will help soften the glue. Blow heat onto the soap bottle holder until it becomes really warm and the heat reaches the adhesive. Move the hair dryer back and forth over the adhesive until it becomes easier to lift from the surface.
NOTE! Sometimes you may need to use the hair dryer for up to 5 minutes, but eventually the adhesive will start to loosen slightly.
Remove the soap bottle holder using a fishing line
Make sure the adhesive is still warm from using the hair dryer. Cut a piece of fishing line so that you can wrap it around your fingers. The fishing line should now be pulled behind the soap bottle holder to easily remove the product from the wall.
Remove any remaining adhesive
Once you have removed the product from the wall, there may be adhesive residue left. Use more heat from the hair dryer and remove the 3M tape with your hands. By rubbing or rolling the tape against the wall, you can gradually loosen it from the surface. If you are unable to remove all the tape with heat, an effective method is to use oil or alcohol-based cleaning products. Cooking oil can be applied to the tape and left to work for a few minutes to dissolve the adhesive.
Done!
Now you have everything you need to get started – good luck with your new project! Take it step by step and use the guide as support along the way. If you need a recap, you can watch the video below where we show how to do it from start to finish.
Find the right bathroom accessories for your bathroom
20
+ Sizes
From
53.36 €From
66.70 €In stock
20
Fits Base
23.20 € 29 €
In stock
Can you bring the products with you if you’re moving?
- Yes, absolutely! Watch the video to see how to remove the soap bottle holder or shelf in the easiest way.
Do you offer extra adhesive for your 3M products? I would like to move my shelf
- At the moment, we unfortunately do not sell replacement adhesive on our website, but it is available at many hardware stores.
Is the shower shelf water resistant?
- Yes, it is! Our tip is not to mount the shower shelf over grout lines, as there is a risk that water may get behind the shelf and affect the adhesion.
Where can you place a soap bottle holder?
- Almost anywhere you like! In the shower, by the sink, or why not in the kitchen for soap and dishwashing liquid? The possibilities are many!
What is the size of the hole for the soap pump?
- The hole has a diameter of 28 mm, which is the standard size for pump bottles. It would be ideal if all pump bottles had the same measurements, but unfortunately, they don’t.
FUN FACT!
- We offer both soap pumps and soaps from Five Oceans and Meraki that fit perfectly in our soap bottle holders.
- Yes, absolutely! Watch the video to see how to remove the soap bottle holder or shelf in the easiest way.
Do you offer extra adhesive for your 3M products? I would like to move my shelf
- At the moment, we unfortunately do not sell replacement adhesive on our website, but it is available at many hardware stores.
Is the shower shelf water resistant?
- Yes, it is! Our tip is not to mount the shower shelf over grout lines, as there is a risk that water may get behind the shelf and affect the adhesion.
Where can you place a soap bottle holder?
- Almost anywhere you like! In the shower, by the sink, or why not in the kitchen for soap and dishwashing liquid? The possibilities are many!
What is the size of the hole for the soap pump?
- The hole has a diameter of 28 mm, which is the standard size for pump bottles. It would be ideal if all pump bottles had the same measurements, but unfortunately, they don’t.
FUN FACT!
- We offer both soap pumps and soaps from Five Oceans and Meraki that fit perfectly in our soap bottle holders.
You will need:
Hair dryer
Fishing line
Heat the adhesive
Unscrew the bottle that has been attached to the soap bottle holder and take out a hair dryer. Heat from a hair dryer is the most effective method for softening adhesive. By using a hair dryer and holding it a few centimetres from the adhesive, the heat will help soften the glue. Blow heat onto the soap bottle holder so that it becomes really warm and the heat reaches the adhesive. Move the hair dryer back and forth over the adhesive until it becomes easier to lift from the surface.
NOTE! Sometimes you may need to use the hair dryer for up to 5 minutes, but eventually the adhesive will start to loosen slightly.
Remove the soap bottle holder using a fishing line
Make sure the adhesive is still warm from using the hair dryer. Cut a piece of fishing line so that you can wrap it around your fingers. The fishing line should now be pulled behind the soap bottle holder to easily remove the product from the wall.
Remove any remaining adhesive
Once you have removed the product from the wall, there may be adhesive residue left. Use more heat from the hair dryer and remove the 3M tape with your hands. By rubbing or rolling the tape against the wall, you can gradually loosen it from the surface. If you are unable to remove all the tape with heat, an effective method is to use oil or alcohol-based cleaning products. Cooking oil can be applied to the tape and left to work for a few minutes to dissolve the adhesive.
Done!
Now you have everything you need to get started – good luck with your new project! Take it step by step and use the guide as support along the way. If you need a recap, you can watch the video below where we show how to do it from start to finish.
Find the right bathroom accessories for your bathroom
20
+ Colours
97.12 € 121.40 €
In stock
20
+ Colours
97.12 € 121.40 €
In stock
20
+ Colours
74.80 € 93.50 €
In stock
20
+ Colours
74.80 € 93.50 €
In stock
20
+ Sizes
From
72.08 €From
90.10 €In stock
20
+ Sizes
From
72.08 €From
90.10 €In stock
20
+ Sizes
72.08 € 90.10 €
In stock
Can you bring the products with you if you’re moving?
- Yes, absolutely! Watch the video to see how to remove the soap bottle holder or shelf in the easiest way.
Do you offer extra adhesive for your 3M products? I would like to move my shelf
- At the moment, we unfortunately do not sell replacement adhesive on our website, but it is available at many hardware stores.
Is the shower shelf water resistant?
- Yes, it is! Our tip is not to mount the shower shelf over grout lines, as there is a risk that water may get behind the shelf and affect the adhesion.
Where can you place a soap bottle holder?
- Almost anywhere you like! In the shower, by the sink, or why not in the kitchen for soap and dishwashing liquid? The areas of use are many!
What is the size of the hole for the soap pump?
- The hole has a diameter of 28 mm, which is the standard size for pump bottles. It would be optimal if all pump bottles had the same measurements, but unfortunately, they don’t.
FUN FACT!
- We have both soap pumps and soaps from Five Oceans and Meraki that fit perfectly in our soap bottle holders.
- Yes, absolutely! Watch the video to see how to remove the soap bottle holder or shelf in the easiest way.
Do you offer extra adhesive for your 3M products? I would like to move my shelf
- At the moment, we unfortunately do not sell replacement adhesive on our website, but it is available at many hardware stores.
Is the shower shelf water resistant?
- Yes, it is! Our tip is not to mount the shower shelf over grout lines, as there is a risk that water may get behind the shelf and affect the adhesion.
Where can you place a soap bottle holder?
- Almost anywhere you like! In the shower, by the sink, or why not in the kitchen for soap and dishwashing liquid? The areas of use are many!
What is the size of the hole for the soap pump?
- The hole has a diameter of 28 mm, which is the standard size for pump bottles. It would be optimal if all pump bottles had the same measurements, but unfortunately, they don’t.
FUN FACT!
- We have both soap pumps and soaps from Five Oceans and Meraki that fit perfectly in our soap bottle holders.
