Assembly of products with 3M tape
Assembly of products with 3M tape

Assembly of products with 3M tape

In our assortment, there is a wide range of products that are attached with 3M tape. The benefits of this are many! Avoid drilling and keep your walls intact, renew and change with products with a long shelf life. We at Beslag Online have put together an assembly guide to facilitate that follows below.

  
About 3M Tape  

3M is a well-known company worldwide that wants to simplify life and the standard of living with innovation and smart products. 3M has developed a double-sided adhesive tape called 3M tape, a quality-safe tape with immediate adhesion.

Optimal surfaces

Before you order your new interior details, it is good to find a place for where you want them to sit.
Then you have the chance to find the most optimal surface that extends both the durability and longevity of the product!

The absolute best possible surfaces are the following; Tile, Varnished or veneered board materials.
Areas to avoid; Wallpaper/tissue, uneven/Rugh surfaces and wet room loss. 

The reason why tiles are one of the best surfaces for attachment is because they are attached to the wall, plus they usually have a smooth, glossy surface which means that the 3M tape will have optimal adhesion. The same principle applies to lacquered and veneered board materials. These materials are also not damaged if you would like to disassemble and replace products in the future. If you would like to attach the products to a wall that is wallpapered or woven, there is a risk during loading that not only the product will come down, but also the wallpaper or fabric. When adhering to rough or uneven surfaces, the adhesive ability of the tape deteriorates. It then becomes more difficult for the tape to contact the entire surface. Surfaces, such as wet room wallpaper, tend to slip and therefore it becomes more difficult for the tape to adhere.


Find your new products 

Once you have determined which surface you want to attach your new interior details to, it is time to be inspired and find your new favorites. In the menu bar at the top of the page you will find Bathroom accessories, once in the category you can choose to specify by colour/material, product type or if you are interested in a special product series. We have a wide range of products that are attached with 3M tape, such as hooks, toilet roll holders, shelves and towel racks.


Preparations

For the best possible results and durability, we recommend that you follow the steps below:

1. Location  

To get the optimal placement on your products, we recommend that you use a spirit level, especially when installing towel rails and shelves. For example, if the product is to be mounted on different tiles, it is important to check that the mounting tiles are at the same level and that they have the same angle. This is because it is optimal with an even weight distribution over the entire product, for the best possible results and durability. Therefore, feel free to measure out where and how you want the product to sit.



2. Cleaning

Start by cleaning the surface with water, feel free to use a spray bottle to distribute the water. Then wipe off the water with a dry cloth. Instead of detergent, use a cleaning cloth when mounting 3M your product. You can find your 3M surface cleaner sachet here. The use of the 3M sachet improves the product's adhesion as it effectively removes dirt, grease and other unwanted particles.





- For example, if you have newly tiled walls, it is important to make sure
that there is no sealant or construction dustleft on the mounting surface. -


Mounting

Once you have cleaned the surface, it is time to attach your new products. You do the following:

1. Remove the protective film.



2. Apply the product by pressing it against the cleaned surface, try to keep an even pressure for about 10 seconds.



3. For optimal adhesion, we recommend allowing the adhesive to cure for at least 24 hours before loading the product.



4. 24 hours later the product is ready to use!

Maintenance 

When it is time to clean the product, we recommend that you use a clean, damp, wrung-out cloth. Depending on the material, the product may be damaged by cleaning agents and the surface may change.

Enjoy your new details, it is usually the small, that makes the whole!
3M Surface Cleaner Sachet /bilder/artiklar/liten/60404-BO_S.jpg?m=1644931320
€2.90
Base 220 3-Hook - Matte Black /bilder/artiklar/liten/61620-21_S.jpg?m=1629380899
Beslag Design
Self-adhesive 3M-tape
€20.80
Base 210 2-Hook - Brushed Stainless Steel Finish /bilder/artiklar/liten/61411-21_S.jpg?m=1628838402
Beslag Design
Self-adhesive 3M-tape
€13.20
Base 210 1-Hook - Chrome /bilder/artiklar/liten/61402-21_S.jpg?m=1628839456
Beslag Design
Self-adhesive 3M-tape
€8.50
Base 220 1-Hook - Polished Brass /bilder/artiklar/liten/61603-21_S.jpg?m=1629357535
Beslag Design
Self-adhesive 3M-tape
€8.60